CODA60 Installation Guide

CODA60 Installation Guide

Follow this step-by-step guide to install your Hitron CODA60 cable modem, activate Internet service, and connect your home network.

The CODA60 supports DOCSIS 3.1 and DOCSIS Ultra 3.1 service, with DOCSIS 4.0 upgrade capability when supported by your Internet Service Provider (ISP).

It also features a 10 Gigabit Ethernet port for connecting compatible routers and network equipment.


Before You Begin

You will need:

  • Hitron CODA60 cable modem.

  • Supplied power adapter.

  • Coaxial cable.

  • Ethernet cable.

  • An active Internet subscription from a compatible ISP.

  • A separate WiFi router or mesh system if you want wireless connectivity.


Step 1: Disconnect Your Old Cable Modem

If you are replacing an existing cable modem:

  1. Disconnect power from your old modem.

  2. Disconnect the coaxial cable.

  3. Remove the old modem.

  4. Place your new CODA60 in the same location.

If this is a new installation, place the CODA60 near an active coaxial cable outlet and an electrical outlet.


Step 2: Connect the Coaxial Cable

  1. Locate the coaxial cable connector on your CODA60.

  2. Connect the provided coaxial cable to the modem.

  3. Connect the other end to your cable wall outlet.

  4. Make sure both connections are securely tightened.


Step 3: Connect Power

  1. Connect the supplied power adapter to the CODA60.

  2. Plug the adapter into an electrical outlet.

  3. Allow the modem to begin its startup process.

The LED will initially display solid green, indicating that the modem is receiving power and booting.


Step 4: Wait for the Modem to Come Online

Allow up to 10 minutes for your CODA60 to connect to your ISP's network.

During startup, you may see:

LED Status
Meaning
Solid Green
Modem is booting.
Alternating White and Green
Searching for a downstream frequency.
Blinking White
Connecting to the DOCSIS network and downloading configuration information.
Solid White
Modem is online.

If the LED does not become solid white, check the coaxial cable connections.

If the problem continues, contact your ISP to verify that your Internet service is activated.


Step 5: Activate Your CODA60

Your ISP must activate your CODA60 before you can use your Internet service.

  1. Locate the CM MAC address on the modem's product label.

  2. Follow the activation instructions provided by your ISP.

  3. Provide the CM MAC address when requested.

  4. Allow the modem to complete the activation process.

The CODA60 is approved for use with GCI and Midco. Confirm compatibility with your service plan and address before activation.


Step 6: Connect Your Router or Computer

Once the CODA60 is online:

  1. Locate the orange 10 Gigabit Ethernet port on the back of the modem.

  2. Connect one end of an Ethernet cable to this port.

  3. Connect the other end to your router's WAN or Internet port.

If you do not have a router, you can connect the Ethernet cable directly to a computer.

Important: The CODA60 does not have built-in WiFi. A separate router or mesh system is required for wireless Internet access.


Step 7: Restart Your Router

If you connected a router:

  1. Disconnect power from the router.

  2. Wait 30 seconds.

  3. Reconnect power.

  4. Allow the router to establish its Internet connection.


Step 8: Test Your Internet Connection

  1. Turn on your computer, smartphone, or tablet.

  2. Connect to your router using WiFi or Ethernet, or use a direct Ethernet connection to the CODA60.

  3. Open a web browser.

  4. Visit a website to verify that your Internet connection is working.

Your ISP may automatically redirect you to an activation website if additional setup is required.


Step 9: Register Your Product

Register your CODA60 with Hitron for future support.

Register Your Hitron CODA60


What If My CODA60 Doesn't Connect?

Check the LED status:

  • Blinking Red: The modem is not receiving a DOCSIS signal. Check the coaxial cable and contact your ISP.

  • Slow Blinking Red: The modem is experiencing a provisioning issue. Contact your ISP.

  • Solid Red: The modem is experiencing a hardware failure. Contact Hitron Technical Support.

  • Alternating White and Cyan: A software update is in progress. Do not disconnect power.


Info

Need More Help?

If you need additional assistance, our Technical Support Team is available 7 days a week, from 6:00 AM to 8:00 PM PT. Visit https://us.hitrontech.com/contact-support/ to chat live with a support agent and get immediate help with your Hitron device.